1. Adopt high-efficiency energy-saving water pump and high-efficiency low-loss motor, and improve the efficiency of the transmission device.
2. Correctly select the power of the pump motor. Prevent "big horse carts". Replace the pump motor with an excessive capacity.
When the motor power is much larger than the actual need, the method of replacing the motor can be used to save power.
3. Choose a reasonable lift.
When the pump's head has a surplus. Power will be wasted, so the head of the pump's operating point should be reasonably determined.
4. Reduce pipe resistance.
Eliminate excess pipe fittings and unnecessary turns and sharp angles on the pipe to reduce pipe resistance and reduce the unit power consumption of the water. Ways to reduce pipe resistance are:
1. The pipeline design should be reasonable.
2. Increase the pipe diameter or use double pipe drainage to reduce the flow rate.
3, as long as possible to shorten the length of the pipe, reduce joints, elbows and valves, especially to avoid the appearance of acute angles.
4. Improve the finish of the inner wall of the pipe or add coating.
5. Remove the dirt on the inner wall of the pipeline in time.
5. The pump speeds and saves electricity.
The power consumption of the pump is proportional to the cube of the unit's speed, so the unit speed is changed according to the actual load conditions. Can greatly save energy. The pump speed control measures are adopted, and the initial investment is large, but the power saving effect is remarkable, and is especially suitable for a large-capacity water pump. It should be noted that the larger the lift, the flatter the resistance curve, and even if the rotational speed is slightly changed, the flow rate will vary greatly, and the power saving effect is poor.
6. Renovate the pump impeller.
When the pump flow in use is larger than the actual required flow rate, and the speed control or the speed control device cannot be used, the original pump impeller can be turned or replaced by the impeller to reduce the flow rate and reduce the flow rate. Head to reduce the running power consumption of the pump.
7. The multi-stage pump adopts pumping operation.
If the multi-stage pump has excess pressure, it can be removed 1 to 2 to achieve efficiency and reduce loss. You can remove any level 1 in the middle when pumping 1 level, and remove 2, 4 or 3 or 5 levels in the middle level. The first and second levels are not pumped.
3.With track chassis and rotary device, easy and speedy to move
4.With hydraulic rod clamp and twist device, reduce auxiliary operation time and labor intensity
5.The major components in hydraulic system adopt the imported brand with a stable, reliable system, and they all have a long service life
6.Top-drive head driven by hydraulic, Continuously Variable speed regulation
7.Variable hydraulic system with load feedback, low energy consumption
8.With display unit for rotating speed of top-drive head, lift speed and verticality of derrick, quickly and accurately to fix position
9.Provide different top-drive head types, meet varying drilling technology
10.The main unit performance:
11. The hydraulic system adopts the direct dynamic fine-tuning variable load feedback system;
12. The main valve adopts the Italian Bloch pooh brand;
13. The main hydraulic pump is Italy Lishile joint technology
14. Walking motor uses the South Korean brand;
15. Equipped with hydraulic gripper, which can automatically remove the drill pipe
2. Correctly select the power of the pump motor. Prevent "big horse carts". Replace the pump motor with an excessive capacity.
When the motor power is much larger than the actual need, the method of replacing the motor can be used to save power.
3. Choose a reasonable lift.
When the pump's head has a surplus. Power will be wasted, so the head of the pump's operating point should be reasonably determined.
4. Reduce pipe resistance.
Eliminate excess pipe fittings and unnecessary turns and sharp angles on the pipe to reduce pipe resistance and reduce the unit power consumption of the water. Ways to reduce pipe resistance are:
1. The pipeline design should be reasonable.
2. Increase the pipe diameter or use double pipe drainage to reduce the flow rate.
3, as long as possible to shorten the length of the pipe, reduce joints, elbows and valves, especially to avoid the appearance of acute angles.
4. Improve the finish of the inner wall of the pipe or add coating.
5. Remove the dirt on the inner wall of the pipeline in time.
5. The pump speeds and saves electricity.
The power consumption of the pump is proportional to the cube of the unit's speed, so the unit speed is changed according to the actual load conditions. Can greatly save energy. The pump speed control measures are adopted, and the initial investment is large, but the power saving effect is remarkable, and is especially suitable for a large-capacity water pump. It should be noted that the larger the lift, the flatter the resistance curve, and even if the rotational speed is slightly changed, the flow rate will vary greatly, and the power saving effect is poor.
6. Renovate the pump impeller.
When the pump flow in use is larger than the actual required flow rate, and the speed control or the speed control device cannot be used, the original pump impeller can be turned or replaced by the impeller to reduce the flow rate and reduce the flow rate. Head to reduce the running power consumption of the pump.
7. The multi-stage pump adopts pumping operation.
If the multi-stage pump has excess pressure, it can be removed 1 to 2 to achieve efficiency and reduce loss. You can remove any level 1 in the middle when pumping 1 level, and remove 2, 4 or 3 or 5 levels in the middle level. The first and second levels are not pumped.
Jet Grouting Rig Features:
1.With multi-directional change-range mechanism, convenient to drill a series of holes with different heights and angles at the same position
2.High rotary torque and longer stroke, high drilling efficiency3.With track chassis and rotary device, easy and speedy to move
4.With hydraulic rod clamp and twist device, reduce auxiliary operation time and labor intensity
5.The major components in hydraulic system adopt the imported brand with a stable, reliable system, and they all have a long service life
6.Top-drive head driven by hydraulic, Continuously Variable speed regulation
7.Variable hydraulic system with load feedback, low energy consumption
8.With display unit for rotating speed of top-drive head, lift speed and verticality of derrick, quickly and accurately to fix position
9.Provide different top-drive head types, meet varying drilling technology
10.The main unit performance:
11. The hydraulic system adopts the direct dynamic fine-tuning variable load feedback system;
12. The main valve adopts the Italian Bloch pooh brand;
13. The main hydraulic pump is Italy Lishile joint technology
14. Walking motor uses the South Korean brand;
15. Equipped with hydraulic gripper, which can automatically remove the drill pipe
Jet Grouting Rig,Jet Grouting Grilling Rig,Tower Pressure Grouting Rig,Omnibearing Rotary Jet Grouting Grilling Rig
Henan YK Prospecting Machinery Co., Ltd , https://www.yydthdrillingrig.com