| No. |       item | Parameter(all is subject to our final design) | |
| 1 Â |
Suitable raw material | Type | Common galvanized & pre-painted steel |
| Yield strength | 235MPa(or other high strength steel) | ||
| Thickness(mm) | 0.4-0.7 | ||
| width(mm) | According to final design | ||
| 2 | Manual uncoiler's capacity | Max.5tons | |
| 3 | Forming speed(m/min) | About 18-20m/min | |
| 4 | Main motor power(KW) | 7.5kw | |
| 5 | Hydraulic power(KW) | 3kw | |
| 6 | Forming roller groups | Around19-20 groups | |
| 7 | Raw material of forming roller | High quality No.45 steel | |
| 8 | Raw material of cutting blade | Cr12mould steel with quenched treatment | |
| 9 | controlling system | Mitsubishi PLC& converter | |
| 10 | Suitable industrial voltage |  According to your special requirement | |
| 11 | Machine dimensions(L*W*H) | 6.8m×1.8m×1.52m | |
| 12 | Machine weight | About 9-10tons | |
Roof Panel Roll Froming Machine; Steel Corrugated Sheet Forming Machine; Steel Sheets Forming Machine; Roll Forming Machine; Forming Machine; Cold Roll Forming Machine; Steel Corrugated Forming Machine.
Components:
The Uncoiler and Its Base
Coil Sheet Guiding and Adjusting Equipment
Film Covered Device
Main Roll Forming System
Post-Cutting Device
Hydraulic Station
PLC Control System
Support Table
The Technical Parameters:
Suitable Raw Material: Color Steel Sheet; Galvanized Steel Sheet
Thickness of The Material: 0.4m to 0.7mm
Yield Strength of Material: 235mpa
Uncoiler's Loading Capacity: Max. Capacity: 5000kgs. (Can Be Increased to Be 10 Tons)
Forming Speed: About 15m/Min
Main Motor Power: 5.5kw(Depend on Final Design)
Hydraulic Station Power: 2.2kw(Depend on Final Design)
Controling System: Mitsubishi PLC & Converter
Voltage: 380V, 3 Phase 60Hz or According to at Buyer's Requirment.
The Quantity of The Roller Group: At Lest 15 Groups(Depend on Final Design)
Machine Dimension: About 20m*1.5m*1.4m(Depend on Final Design)
Total Weight: About 10000kgs(Depend on Final Design)
Material of Roll Former System
Roller: High Grade No. 45 Forged Steel, Plated Hard Chromed on The Surface of Rollers
With Thickness 0.05mm.
Active Shaft Material: High Grade No. 45 Carbon Wrought Steel at Diameter 75mm.
Cutting Blade: Cr12 Mould Steel with Quenched Treatment.
Working Flow
Decoiling The Sheet---Guiding The Sheet---Covering The Film---Roll Forming---Measuring The Length---Cutting The Panel---Panels to The Supporter
Leisuwash S90 Vehicle Wash System
Leisuwash specializing in manufacture Automatic Car Wash Machine, Touchless Car Wash , Automatic Touchless Car Wash, touchless car wash equipment, robot car wash, smart car wash system, leisuwash 360, leisuwash leibao 360, laserwash 360, leisuwash touchless car wash machine, leisu wash touchless car wash automatic, leisu wash 360 high pressure touchless car wash equipment, robo car wash, touch free car wash, leisuwash 360 touch free car wash, leisuwash 360 price, automatic car wash price, leisuwash in malaysia, no touch automatic car wash machine, leisuwash 360 mini, leisuwash SG fully automatic car wash equipment.
Leisuwash S90 touchless car wash machine high intelligent high quality, with car wash + car care + drying process totally, each car wash takes time 1 minute to 5 minutes which depends on the car wash mode.
Leisuwash S90 Car Wash Machine is an entry level car wash unit, but you won`t find any low grade components and no cost cutting on the expense of quality. Each Leisuwash S90 is built by Leisuwash employees in accordance with our usual quality standards, the low price is achieved by high standardization and the use of proven technology. The Leisuwash S90 is for clients that need a wash machine at a competitive price with higher ROI.
Auto Car Wash Machine,Automatic Leisuwash S90 Series,Leisuwash S90 Series Car Wash Machine,Automatic Leisuwash S90 Series Car Wash Machine
Hangzhou Leisu Cleaning Equipment Co.,Ltd , https://www.sdlaserwash.com