Hainan × × fluorite ore is a quartz -fluorite deposit, the ore-forming temperature is low, the fluorite crystallization is incomplete, the size of the inlay is fine, and the quartz inlay is closely related. The fluorite is difficult to dissociate from the monomer, which is a fine-grained intercalation. The refractory fluorite deposit, whose main harmful impurity is SiO2, the other impurities such as S, P, CaCO3 do not pose a hazard to the concentrate product.
Rock ore identification shows that most of the fluorite in the ore is easily dissociated. When grinding to -200 mesh 75%, 85% of the monomer has dissociated, but a small part of the fluorite is extremely difficult to dissociate until the fineness When it reaches 95% of -200 mesh, it is possible to obtain the ideal index. If this grinding degree is achieved by a section of grinding, it is obviously uneconomical. The ore dressing test results show that the ore can obtain qualified concentrate under the condition of -200 mesh 75-80% grinding fineness, and the open circuit recovery rate is about 65%. The grinding degree can be improved by a section of grinding, and the product quality can be appropriately improved. However, the recovery rate is reduced; the re-grinding test of coarse concentrate shows that it is difficult to improve the grinding degree and the ore dressing index; under a period of grinding-200 mesh 80% fineness, the closed-circuit beneficiation test is carried out, and the following index is obtained: CaF298. 35%, SiO20.94%, CaCO30.35%, recovery rate 74.40%.
For the ore, our view is: the design uses two-stage grinding, one section of grinding -200 mesh 75-80%, the coarse concentrate is selected by 5-7 times, fine 1~3 mine and sweeping foam products Feed the second section of grinding, the second section of grinding products return to the flotation process (see process flow chart). The medium-mine regrind scheme is superior to the coarse concentrate re-grinding scheme, because 85% of the fluorite mineral monomer has been dissociated when the mine is milled to -200 mesh 75%, and the coarse concentrate re-grinding will cause the monomer to dissociate. The over-grinding of the mineral is not conducive to the subsequent selection of the operation; if only a few minerals based on the continuous body are re-ground, the over-grinding of the monomer-dissociated minerals can be avoided, which is beneficial to improve the process index and reduce the second stage. Grinding capacity, the advantages are obvious.
The disadvantage of using a section of grinding is that the fluorite dissociation degree is difficult to guarantee, which is not conducive to the improvement of product quality and beneficiation recovery rate. If the grinding degree is increased to -200 mesh 80% or more at one time, the grinding cost will be doubled. . If the investor insists on adopting a grinding process, part of the ore in the flotation process should be concentrated and returned to re-grind, but in this part of the regrind, whether the fineness of the mill reaches the monomer dissociation, it is impossible to grasp in the production process. The additional ore dressing consumption will be much larger than the second-stage grinding (mainly in the treatment of low ore). Therefore, we still advocate the use of the second-stage grinding-mineral regrind process.
Operated with Computer Numerical Control (CNC) systems and provided with precise design instructions, CNC Lathes are machine tools where the material or part is clamped and rotated by the main spindle, while the cutting tool that work on the material, is mounted and moved in various axis.
CNC Lathes are normally used for machining parts, where the material / part is clamped and rotated whereas the cutting tool is stationery mounted for OD (Outer Diameter) and ID (Inner Diameter) operations, e.g. shafts and pipes. They are ideal for parts that have same symmetry around an axis that could be chucked up (i.e. radially clamped) in the spindle.
A simple CNC Lathe operates on 2-axis and the tool is located in a fixed position at 8 to 24 station turret. The rotating action of the part is called [turning", hence certain types of CNC Lathes are called CNC Turning Machines.
Milling (cutting tool moves around stationery workpiece), boring and tapping (a tool that cuts threads inside hole) tools are normally driven by a separate drive system inside the turret. Depending on the application, the life tools (i.e. active tool) are mounted for axial or radial operational directions. These could be found in 3-axis CNC Lathes or CNC Turning Machines.
Lathe machines with additional options such as Y-axis, sub-spindles, or specific selected options for automation are commonly called Turning Centres. These sophisticated machine tools are capable of machining complex parts – these go beyond standard OD & ID turning operations and may incorporate milling, drilling and tapping operations to complete the part in one setting. Taking a piece from raw part to finished product, such all-in-one machine tools significantly improves productivity.
Cnc Lathe,Cnc Lathe Machine,Cnc Lathe For Sale,Cnc Lathe Machine Price,CNC Lathe at a Favorable Price
Jiangsu Hoston Machine Tools Co., Ltd. , https://www.hosdunmachinetools.com